Added to your cart
Edit cartFinal PRO with 500 ml degreaser, 4 applicators and 10 microfibre cloths — a coordinated kit for applying your ceramic coating.
*Depending on preparation, application, use and maintenance.
Taxes included
Delivery: 1–3 business days · Germany
Guideline: approximately 35 ml for the paintwork of a Golf-sized car.
50 ml Final PRO: Usually enough for the paintwork of a Golf-sized car.
100 ml Final PRO: Extra capacity for larger vehicles, additional suitable surfaces or multiple vehicles.
Both kits include 500 ml Ultra Degreaser, 4 applicators and 10 microfibre cloths. Only the amount of ceramic coating changes. Actual consumption depends on the surface area and application method.
Instructions and coating certificates are included. Accessory quantities are the same for both sizes.
Suitable for: Automotive paints, painted rims, as well as suitable vehicle wraps and plastics.
Matte paints and wraps: Test on an inconspicuous area beforehand to ensure the surface appearance remains unchanged. If in doubt, consult with us before application.
Not for glass or soft rubber seals. Always test for compatibility on an inconspicuous area before each use.
Work at 15–25 °C on cool, dry surfaces. Provide good lighting and ventilation, wear protective equipment and check compatibility.
Prepare: Clean, remove bonded contamination and always polish gloss paintwork — even new cars need at least a finishing polish. Shake Ultra Degreaser before use, spray undiluted onto a suitable surface, allow to dwell briefly and wipe with a soft, dry cloth. Allow to dry completely and work in a dust-free environment.
Apply: Distribute a small amount of Final PRO through the supplied applicator; start with an area no larger than approximately 60 × 60 cm. After about 3 minutes, level with the supplied 300-gsm cloths without pressure.
Inspect: Check for coating residue from several lighting angles. Gently wipe away fresh high spots no later than 10 minutes after application.
Cure: 12 hours until water-resistant and ready to drive; 5 days until fully cured. These are approximate times at around 20 °C and depend on the climate. Keep dry and protected until water-resistant; do not wash for 5 days. Carefully remove bird droppings and heavy contamination with a gentle stream of water or a very soft microfibre cloth.
View application steps →Is this the same coating as the individual bottle?
Yes. You receive Final PRO in your chosen size. The kit adds degreaser and accessories for application and levelling.
What else do I need?
Products and equipment for washing and polishing the vehicle, good lighting, a sheltered workspace and suitable protective equipment. Always polish gloss paintwork — even new cars need at least a finishing polish.
Is the kit suitable for beginners?
Application is possible with careful preparation and some car-care experience. Watch the product video and read the instructions first. Contact our technical support if you are unsure.
Can I reuse the cloths afterwards?
Use separate cloths for degreasing, levelling and inspection. Cured coating residue can harden the fibres. Do not reuse affected cloths or applicators on sensitive surfaces.
How long does Final PRO last?
Up to 3 years, depending on preparation, application, use and maintenance. Wash regularly and remove heavy contamination promptly.
Final PRO and Ultra Degreaser: made in Germany.
Application instructions (PDF) ↗ Safety data sheet (PDF) ↗ View the full test report ↗
Safety informationUltra Degreaser
Causes serious eye damage. EUH208: Contains orange, sweet, extract. May produce an allergic reaction.
Keep out of reach of children. Wash hands thoroughly after handling. Wear protective gloves, protective clothing and eye/face protection. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get immediate medical advice/attention. Dispose of contents/container in accordance with official regulations.
Final PRO in a kit
After polishing the paintwork, remove residue with Ultra Degreaser. The applicators spread Final PRO evenly; the soft 300-gsm cloths help you remove excess coating and inspect the result. This keeps the right products for the coating process close at hand.
Documented inspection
The Final PRO coating included in the kit underwent artificial weathering at the DEKRA Automobil GmbH laboratory in Bretten. The coating's appearance and adhesion were among the properties assessed afterwards.
Open test report
Artificial weathering in a hot, dry climate. No visible cracking on the tested samples.
No coating delamination in the cross-cut test after weathering.
Application
Work at 15–25 °C on cool, dry surfaces. Read the instructions and safety information beforehand.
Wash, polish gloss paintwork and degrease thoroughly with Ultra Degreaser. Work in dry, dust-free conditions.
Spread Final PRO in sections using the applicator. After about 3 minutes, level with a fresh 300-gsm cloth without pressure.
Check with a separate cloth. Gently wipe away fresh coating residue within 10 minutes; leave the coating to cure in a sheltered area.
12 hours until water-resistant and ready to drive ·
5 days until fully cured
Guideline values at approx. 20 °C, depending on climatic conditions. Keep dry until water-resistant; do not wash for the first 5 days.
